The minimum average relative error (RE) of the predictive values for the validation samples was %, and the average error of the proposed model for the calorific value quantitative analysis was MJ kg −1.
The pulverized coal was dried at three selected temperatures of 25 °C, 75 °C and 110 °C, and the moisture and porosity of the pulverized coal particles were measured. Based on the porosity range obtained from the measurement, 3D steady numerical simulation of combustion in tangentially coalfired furnace was conducted by use of Fluent Software.
recovered fuel (SRF). RDF had only two classes depending only on the calorific value, moisture and ash content, in contrast to 125 SRF classes. These SRF classes are based on three properties where each of the properties has five classes for the net calorific value, the chlorine content, and the mercury content [8].
The biomass and coal samples were dried (according to ASTM D3302) and pulverized to obtain a size of less than 250 μm for characteristics tests such as proximate, ultimate, calorific value, and total chlorine. For the DTF combustion experiment and thermogravimetric analysis, the coal was pulverized to a particle diameter smaller than 75 μm.
When there was no condition to test the coal calorific value in the industry, the net calorific value of coal could be calculated according to the empirical formula [30]. By contrasting the net calorific values of coal obtained by experience formula and experiment, LIU and JU [31] found that the deviation was less than 5%. It was shown
The measurement repeatability meets the requirements of the Chinese national standard. This calorific value measurement technology based on NIRSXRF is safe, fast, and stable, providing a new way to optimize and control the utilization process of coal in coal washing plants, power plants, coking, and other industries.
the input of sulfur, hydrogen, total water and analytic water; the high calorific value, low calorific value and cartridge calorific value of coal can be calculated automatically [910]. The difference between high calorific value and low calorific value lies in whether the water in fuel combustion products is liquid or gaseous. Water is liquid ...
The coal consumption in our country mainly lies in coalfired power stations and industrial boilers. 1 Since the temperature change in the furnace influences combustion, slagging, corrosion, and so on, 2 the accurate analysis of the temperature level and its distribution in the furnace will predict the slagging in the furnace and improve the saf...
The given values are for fuels with the given density. The variation in quality may give heating values within a range 5 10% higher and lower than the given value. Also the solid fuels will have a similar quality variation for the different classes of fuel. 1 Btu (IT)/lb = MJ/t = J/kg = kcal/kg = kWh/kg.
With the slagging index (R S) when the test coal ash mass ratio for C 1 /C 2 is 1:1, comparable values can be obtained for a mixture of coal ashes with biomass B 1 ash additions in the ratio of C 1 /C 2 /B 1 —15:70:15 (Fig. 3b), for which the amount of fuel directed to the comass ratio (of raw dry fuels) was 7:37:56 m/m.
The combustion efficiency of a coal is often measured in terms of burnout. In this study, the ash tracer method [21], [22] was adopted to determine the burnout of the tested coals. The burnout can be expressed as (1) Burnout (%) = A s h u c − A s h r c A s h u c (1 − A s h r c 100) × 100 where Ash uc and Ash rc stand for ash contents in the unburned char and the raw coal, respectively.
Pulverized Coal Combustion. PCC technology is a widely utilized technology to generate energy from fossil fuel, especially coal [15]. In this technology, pulverized coal is injected to combust in a furnace in the presence of a controlled level of air. The heat generated is used to produce highpressure steam driving a steam turbine to ...
It uses coke and auxiliary injectants like pulverized coal (PC) to generate the reductants and energy needed. However, coke production causes considerable energy consumption and greenhouse emissions and accounts for a big portion of pig iron production costs [1]. Also, coking coal resource is gradually depleted on the earth.
error (ARE), and the standard deviation (SD) of this method for predicting the calori c value of coal are fi MJ kg−1, % and MJ kg−1 respectively. The measurement repeatability...
A commentary has been published: Discussion: "PulverizedCoal Firing of Marine WaterTube Boilers: Following Upon an Appreciation of the Results Secured in the Stationary PowerPlant Field With Pulverized Coal, a Series of Tests Were Conducted to Determine the Value of This Method of Firing to Marine Boilers" (Stillman, T. B., 1928, Trans. ASME, 4950(3), p. 031066)
The average values of the 002 peak positions of semicoke and pulverized coal are relatively close, and both are smaller than the average value corresponding to the 002 peak of coke breeze. The 002 peak positions of semicoke and pulverized coal have large ranges of fluctuation, which are °° and °°, respectively.
The new equation is at least as effective in predicting calorific values for a set of 1004 coals as equiv. equations derived for 6 subsets of the coals. On the whole, the distributions of differences between obsd. and calcd. calorific values are skewed to only a small extent. About 86% of the differences lie between 300 and +300 Btulb.1.
Heating value and vitrinite reflectance are both rank parameters (section ); although, as noted in section, calorific value is related to the maceral content as well as the coal rank. Grindability and particle size are also related ( section ), with particle size being a function of the grindability of the coal and the energy ...
Though several factors affect the calorific value, including the type of coal, particle size, and environmental conditions [2530]. The scope of this work is limited to explore the effect of environmental factors (temperature, humidity, and air flow) on low grade coal pulverized to obtain average particle size of 213 μm, according to ...
At present, coalfired power plants mainly involve pulverized coal combustion and a great amount of coal combustion solid residue continues to be formed from power plants. Querol et al. [2] have estimated the worldwide production of coal ash to exceed 550 × 10 6 tonnes/year. Fly ash is defined as the fraction of fine ash particles that is ...
Calorific value is an essential fuel parameter during the process of energy utilization. Fortyfour coal samples with different calorific values were quantitatively analyzed by laserinduced breakdown spectroscopy (LIBS) in this paper. The influences of different spectral preprocessing methods such as smoothing, standard normal variate transformation (SNV), multiplicative scatter correction ...
The adiabatic bomb calorimeter and the isothermal bomb calorimeter are two standard methodologies defined by GB/T [3], ISO 1928 2009 (E) [4] and ASTM D586513 [5]. In bomb calorimetry, coal burns in a bomb, and the heat of combustion is transferred to water outside the bomb wall.
© DZCrusher - كل الحقوق محفوظة
